给导热油锅炉加热该注意什么呢? - 山东多介质过滤器哪家好
欢迎光临!888贵宾会网站登录网址,主营:山东燃气锅炉山东电采暖锅炉山东多介质过滤器和射线防护器材等。
  • 服务热线:18678809986
  • 888贵宾会网站登录网址 关于我们 产品中心 888贵宾会手机版 工程案例 设备选型 联系我们
  • 您的位置:888贵宾会网站登录网址> 888贵宾会手机版 >

    给导热油锅炉加热该注意什么呢?
    来源: 发布时间:2020-05-22

      热油锅炉安装完成后,需要一种介质来操作整个锅炉系统,即锅炉热油。人们通常把导热油比作导热油锅炉的血液,那么当导热油投入使用时应该注意些什么呢?
      After the installation of the hot oil boiler, a medium is needed to operate the whole boiler system, that is, the hot oil of the boiler. People usually compare the heat-transfer oil to the blood of the heat-transfer oil boiler. What should we pay attention to when the heat-transfer oil is put into use?
      锅炉厂家答应用热油锅炉到炉膛和管道停止清理,清除炉膛内杂质的铁锈和水汽,确保设备的使用干净;当冷油注入热油锅炉高位槽时,温度应在80℃以下参与热油,以防止热油沸腾;热油锅炉开始运行时,启动循环油泵,在冷态运行1-2小时,然后点火加热。
      The boiler manufacturer promises to use hot oil boiler to stop cleaning the furnace and pipes, remove the rust and water vapor of impurities in the furnace, and ensure the use of equipment is clean; when cold oil is injected into the high-level tank of the hot oil boiler, the temperature shall be below 80 ℃ to participate in the hot oil, so as to prevent the boiling of hot oil; when the hot oil boiler starts to operate, start the circulating oil pump, operate in the cold state for 1-2 hours, and then ignite for heating.

      使用导热油锅炉导热油次慢慢加热,温度10℃左右,每小时加热到80 ~ 120℃时应缓慢升温,脱水阶段的时期,这个时候热油泵压力计,压力表等震动,应暂停,恒压火一段时间,待蒸汽排放后继续加热,控制升温速率约20℃/小时。
      Use the heat transfer oil boiler to heat the heat transfer oil slowly for the first time at a temperature of about 10 ℃. When it is heated to 80 ~ 120 ℃ every hour, the temperature shall be raised slowly. During the dehydration stage, when the pressure gauge and pressure gauge of the heat pump vibrate, the temperature shall be suspended and the fire with constant pressure shall be kept for a period of time, and the heating shall be continued after the steam is discharged, and the heating rate shall be controlled at about 20 ℃ / hour.
      锅炉传热油加热到180~220℃时,这一段为减重段。此时,需要将恒温控制一段时间,然后将其提高到工作温度,正常使用。循环系统的热油进入热油锅炉本体前,应安装30-40目不锈钢丝过滤器,将可能产生的焊渣、杂质、残炭等进行过滤。
      When the heat transfer oil of the boiler is heated to 180 ~ 220 ℃, this section is the weight reduction section. At this time, it is necessary to control the constant temperature for a period of time, and then raise it to the working temperature for normal use. Before the hot oil of the circulation system enters the hot oil boiler body, a 30-40 mesh stainless steel wire filter shall be installed to filter the welding slag, impurities and carbon residue that may be generated.

    鲁公网安备 37011302000227号